8139too-2.6.36-ethercat.c

/******************************************************************************
 *
 *  $Id$
 *
 *  Copyright (C) 2006-2009  Florian Pose, Ingenieurgemeinschaft IgH
 *
 *  This file is part of the IgH EtherCAT Master.
 *
 *  The IgH EtherCAT Master is free software; you can redistribute it and/or
 *  modify it under the terms of the GNU General Public License version 2, as
 *  published by the Free Software Foundation.
 *
 *  The IgH EtherCAT Master is distributed in the hope that it will be useful,
 *  but WITHOUT ANY WARRANTY; without even the implied warranty of
 *  MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE.  See the GNU General
 *  Public License for more details.
 *
 *  You should have received a copy of the GNU General Public License along
 *  with the IgH EtherCAT Master; if not, write to the Free Software
 *  Foundation, Inc., 51 Franklin St, Fifth Floor, Boston, MA  02110-1301  USA
 *
 *  ---
 *
 *  The license mentioned above concerns the source code only. Using the
 *  EtherCAT technology and brand is only permitted in compliance with the
 *  industrial property and similar rights of Beckhoff Automation GmbH.
 *
 *****************************************************************************/

/**
   \file
   EtherCAT driver for RTL8139-compatible NICs.
*/

/*****************************************************************************/

/*
  Former documentation:

	8139too.c: A RealTek RTL-8139 Fast Ethernet driver for Linux.

	Maintained by Jeff Garzik <jgarzik@pobox.com>
	Copyright 2000-2002 Jeff Garzik

	Much code comes from Donald Becker's rtl8139.c driver,
	versions 1.13 and older.  This driver was originally based
	on rtl8139.c version 1.07.  Header of rtl8139.c version 1.13:

	-----<snip>-----

        	Written 1997-2001 by Donald Becker.
		This software may be used and distributed according to the
		terms of the GNU General Public License (GPL), incorporated
		herein by reference.  Drivers based on or derived from this
		code fall under the GPL and must retain the authorship,
		copyright and license notice.  This file is not a complete
		program and may only be used when the entire operating
		system is licensed under the GPL.

		This driver is for boards based on the RTL8129 and RTL8139
		PCI ethernet chips.

		The author may be reached as becker@scyld.com, or C/O Scyld
		Computing Corporation 410 Severn Ave., Suite 210 Annapolis
		MD 21403

		Support and updates available at
		http://www.scyld.com/network/rtl8139.html

		Twister-tuning table provided by Kinston
		<shangh@realtek.com.tw>.

	-----<snip>-----

	This software may be used and distributed according to the terms
	of the GNU General Public License, incorporated herein by reference.

	Contributors:

		Donald Becker - he wrote the original driver, kudos to him!
		(but please don't e-mail him for support, this isn't his driver)

		Tigran Aivazian - bug fixes, skbuff free cleanup

		Martin Mares - suggestions for PCI cleanup

		David S. Miller - PCI DMA and softnet updates

		Ernst Gill - fixes ported from BSD driver

		Daniel Kobras - identified specific locations of
			posted MMIO write bugginess

		Gerard Sharp - bug fix, testing and feedback

		David Ford - Rx ring wrap fix

		Dan DeMaggio - swapped RTL8139 cards with me, and allowed me
		to find and fix a crucial bug on older chipsets.

		Donald Becker/Chris Butterworth/Marcus Westergren -
		Noticed various Rx packet size-related buglets.

		Santiago Garcia Mantinan - testing and feedback

		Jens David - 2.2.x kernel backports

		Martin Dennett - incredibly helpful insight on undocumented
		features of the 8139 chips

		Jean-Jacques Michel - bug fix

		Tobias Ringström - Rx interrupt status checking suggestion

		Andrew Morton - Clear blocked signals, avoid
		buffer overrun setting current->comm.

		Kalle Olavi Niemitalo - Wake-on-LAN ioctls

		Robert Kuebel - Save kernel thread from dying on any signal.

	Submitting bug reports:

		"rtl8139-diag -mmmaaavvveefN" output
		enable RTL8139_DEBUG below, and look at 'dmesg' or kernel log

*/

#define pr_fmt(fmt) KBUILD_MODNAME ": " fmt

#define DRV_NAME	"ec_8139too"
#define DRV_VERSION	"0.9.28"


#include <linux/module.h>
#include <linux/kernel.h>
#include <linux/compiler.h>
#include <linux/pci.h>
#include <linux/init.h>
#include <linux/netdevice.h>
#include <linux/etherdevice.h>
#include <linux/rtnetlink.h>
#include <linux/delay.h>
#include <linux/ethtool.h>
#include <linux/mii.h>
#include <linux/completion.h>
#include <linux/crc32.h>
#include <linux/io.h>
#include <linux/uaccess.h>
#include <linux/gfp.h>
#include <asm/irq.h>

#include "../globals.h"
#include "ecdev.h"

#define RTL8139_DRIVER_NAME DRV_NAME \
                            " EtherCAT-capable Fast Ethernet driver " \
                            DRV_VERSION ", master " EC_MASTER_VERSION

#define PFX DRV_NAME ": "

/* Default Message level */
#define RTL8139_DEF_MSG_ENABLE   (NETIF_MSG_DRV   | \
                                 NETIF_MSG_PROBE  | \
                                 NETIF_MSG_LINK)


/* define to 1, 2 or 3 to enable copious debugging info */
#define RTL8139_DEBUG 0

/* define to 1 to disable lightweight runtime debugging checks */
#undef RTL8139_NDEBUG


#ifdef RTL8139_NDEBUG
#  define assert(expr) do {} while (0)
#else
#  define assert(expr) \
        if (unlikely(!(expr))) {				\
		pr_err("Assertion failed! %s,%s,%s,line=%d\n",	\
		       #expr, __FILE__, __func__, __LINE__);	\
        }
#endif


/* A few user-configurable values. */
/* media options */
#define MAX_UNITS 8
static int media[MAX_UNITS] = {-1, -1, -1, -1, -1, -1, -1, -1};
static int full_duplex[MAX_UNITS] = {-1, -1, -1, -1, -1, -1, -1, -1};

/* Whether to use MMIO or PIO. Default to MMIO. */
#ifdef CONFIG_8139TOO_PIO
static int use_io = 1;
#else
static int use_io = 0;
#endif

/* Maximum number of multicast addresses to filter (vs. Rx-all-multicast).
   The RTL chips use a 64 element hash table based on the Ethernet CRC.  */
static int multicast_filter_limit = 32;

/* bitmapped message enable number */
static int debug = -1;

/*
 * Receive ring size
 * Warning: 64K ring has hardware issues and may lock up.
 */
#if defined(CONFIG_SH_DREAMCAST)
#define RX_BUF_IDX 0	/* 8K ring */
#else
#define RX_BUF_IDX	2	/* 32K ring */
#endif
#define RX_BUF_LEN	(8192 << RX_BUF_IDX)
#define RX_BUF_PAD	16
#define RX_BUF_WRAP_PAD 2048 /* spare padding to handle lack of packet wrap */

#if RX_BUF_LEN == 65536
#define RX_BUF_TOT_LEN	RX_BUF_LEN
#else
#define RX_BUF_TOT_LEN	(RX_BUF_LEN + RX_BUF_PAD + RX_BUF_WRAP_PAD)
#endif

/* Number of Tx descriptor registers. */
#define NUM_TX_DESC	4

/* max supported ethernet frame size -- must be at least (dev->mtu+14+4).*/
#define MAX_ETH_FRAME_SIZE	1536

/* Size of the Tx bounce buffers -- must be at least (dev->mtu+14+4). */
#define TX_BUF_SIZE	MAX_ETH_FRAME_SIZE
#define TX_BUF_TOT_LEN	(TX_BUF_SIZE * NUM_TX_DESC)

/* PCI Tuning Parameters
   Threshold is bytes transferred to chip before transmission starts. */
#define TX_FIFO_THRESH 256	/* In bytes, rounded down to 32 byte units. */

/* The following settings are log_2(bytes)-4:  0 == 16 bytes .. 6==1024, 7==end of packet. */
#define RX_FIFO_THRESH	7	/* Rx buffer level before first PCI xfer.  */
#define RX_DMA_BURST	7	/* Maximum PCI burst, '6' is 1024 */
#define TX_DMA_BURST	6	/* Maximum PCI burst, '6' is 1024 */
#define TX_RETRY	8	/* 0-15.  retries = 16 + (TX_RETRY * 16) */

/* Operational parameters that usually are not changed. */
/* Time in jiffies before concluding the transmitter is hung. */
#define TX_TIMEOUT  (6*HZ)


enum {
	HAS_MII_XCVR = 0x010000,
	HAS_CHIP_XCVR = 0x020000,
	HAS_LNK_CHNG = 0x040000,
};

#define RTL_NUM_STATS 4		/* number of ETHTOOL_GSTATS u64's */
#define RTL_REGS_VER 1		/* version of reg. data in ETHTOOL_GREGS */
#define RTL_MIN_IO_SIZE 0x80
#define RTL8139B_IO_SIZE 256

#define RTL8129_CAPS	HAS_MII_XCVR
#define RTL8139_CAPS	(HAS_CHIP_XCVR|HAS_LNK_CHNG)

typedef enum {
	RTL8139 = 0,
	RTL8129,
} board_t;


/* indexed by board_t, above */
static const struct {
	const char *name;
	u32 hw_flags;
} board_info[] __devinitdata = {
	{ "RealTek RTL8139", RTL8139_CAPS },
	{ "RealTek RTL8129", RTL8129_CAPS },
};


static DEFINE_PCI_DEVICE_TABLE(rtl8139_pci_tbl) = {
	{0x10ec, 0x8139, PCI_ANY_ID, PCI_ANY_ID, 0, 0, RTL8139 },
	{0x10ec, 0x8138, PCI_ANY_ID, PCI_ANY_ID, 0, 0, RTL8139 },
	{0x1113, 0x1211, PCI_ANY_ID, PCI_ANY_ID, 0, 0, RTL8139 },
	{0x1500, 0x1360, PCI_ANY_ID, PCI_ANY_ID, 0, 0, RTL8139 },
	{0x4033, 0x1360, PCI_ANY_ID, PCI_ANY_ID, 0, 0, RTL8139 },
	{0x1186, 0x1300, PCI_ANY_ID, PCI_ANY_ID, 0, 0, RTL8139 },
	{0x1186, 0x1340, PCI_ANY_ID, PCI_ANY_ID, 0, 0, RTL8139 },
	{0x13d1, 0xab06, PCI_ANY_ID, PCI_ANY_ID, 0, 0, RTL8139 },
	{0x1259, 0xa117, PCI_ANY_ID, PCI_ANY_ID, 0, 0, RTL8139 },
	{0x1259, 0xa11e, PCI_ANY_ID, PCI_ANY_ID, 0, 0, RTL8139 },
	{0x14ea, 0xab06, PCI_ANY_ID, PCI_ANY_ID, 0, 0, RTL8139 },
	{0x14ea, 0xab07, PCI_ANY_ID, PCI_ANY_ID, 0, 0, RTL8139 },
	{0x11db, 0x1234, PCI_ANY_ID, PCI_ANY_ID, 0, 0, RTL8139 },
	{0x1432, 0x9130, PCI_ANY_ID, PCI_ANY_ID, 0, 0, RTL8139 },
	{0x02ac, 0x1012, PCI_ANY_ID, PCI_ANY_ID, 0, 0, RTL8139 },
	{0x018a, 0x0106, PCI_ANY_ID, PCI_ANY_ID, 0, 0, RTL8139 },
	{0x126c, 0x1211, PCI_ANY_ID, PCI_ANY_ID, 0, 0, RTL8139 },
	{0x1743, 0x8139, PCI_ANY_ID, PCI_ANY_ID, 0, 0, RTL8139 },
	{0x021b, 0x8139, PCI_ANY_ID, PCI_ANY_ID, 0, 0, RTL8139 },

#ifdef CONFIG_SH_SECUREEDGE5410
	/* Bogus 8139 silicon reports 8129 without external PROM :-( */
	{0x10ec, 0x8129, PCI_ANY_ID, PCI_ANY_ID, 0, 0, RTL8139 },
#endif
#ifdef CONFIG_8139TOO_8129
	{0x10ec, 0x8129, PCI_ANY_ID, PCI_ANY_ID, 0, 0, RTL8129 },
#endif

	/* some crazy cards report invalid vendor ids like
	 * 0x0001 here.  The other ids are valid and constant,
	 * so we simply don't match on the main vendor id.
	 */
	{PCI_ANY_ID, 0x8139, 0x10ec, 0x8139, 0, 0, RTL8139 },
	{PCI_ANY_ID, 0x8139, 0x1186, 0x1300, 0, 0, RTL8139 },
	{PCI_ANY_ID, 0x8139, 0x13d1, 0xab06, 0, 0, RTL8139 },

	{0,}
};

/* prevent driver from being loaded automatically */
//MODULE_DEVICE_TABLE (pci, rtl8139_pci_tbl);

static struct {
	const char str[ETH_GSTRING_LEN];
} ethtool_stats_keys[] = {
	{ "early_rx" },
	{ "tx_buf_mapped" },
	{ "tx_timeouts" },
	{ "rx_lost_in_ring" },
};

/* The rest of these values should never change. */

/* Symbolic offsets to registers. */
enum RTL8139_registers {
	MAC0		= 0,	 /* Ethernet hardware address. */
	MAR0		= 8,	 /* Multicast filter. */
	TxStatus0	= 0x10,	 /* Transmit status (Four 32bit registers). */
	TxAddr0		= 0x20,	 /* Tx descriptors (also four 32bit). */
	RxBuf		= 0x30,
	ChipCmd		= 0x37,
	RxBufPtr	= 0x38,
	RxBufAddr	= 0x3A,
	IntrMask	= 0x3C,
	IntrStatus	= 0x3E,
	TxConfig	= 0x40,
	RxConfig	= 0x44,
	Timer		= 0x48,	 /* A general-purpose counter. */
	RxMissed	= 0x4C,  /* 24 bits valid, write clears. */
	Cfg9346		= 0x50,
	Config0		= 0x51,
	Config1		= 0x52,
	TimerInt	= 0x54,
	MediaStatus	= 0x58,
	Config3		= 0x59,
	Config4		= 0x5A,	 /* absent on RTL-8139A */
	HltClk		= 0x5B,
	MultiIntr	= 0x5C,
	TxSummary	= 0x60,
	BasicModeCtrl	= 0x62,
	BasicModeStatus	= 0x64,
	NWayAdvert	= 0x66,
	NWayLPAR	= 0x68,
	NWayExpansion	= 0x6A,
	/* Undocumented registers, but required for proper operation. */
	FIFOTMS		= 0x70,	 /* FIFO Control and test. */
	CSCR		= 0x74,	 /* Chip Status and Configuration Register. */
	PARA78		= 0x78,
	FlashReg	= 0xD4,	/* Communication with Flash ROM, four bytes. */
	PARA7c		= 0x7c,	 /* Magic transceiver parameter register. */
	Config5		= 0xD8,	 /* absent on RTL-8139A */
};

enum ClearBitMasks {
	MultiIntrClear	= 0xF000,
	ChipCmdClear	= 0xE2,
	Config1Clear	= (1<<7)|(1<<6)|(1<<3)|(1<<2)|(1<<1),
};

enum ChipCmdBits {
	CmdReset	= 0x10,
	CmdRxEnb	= 0x08,
	CmdTxEnb	= 0x04,
	RxBufEmpty	= 0x01,
};

/* Interrupt register bits, using my own meaningful names. */
enum IntrStatusBits {
	PCIErr		= 0x8000,
	PCSTimeout	= 0x4000,
	RxFIFOOver	= 0x40,
	RxUnderrun	= 0x20,
	RxOverflow	= 0x10,
	TxErr		= 0x08,
	TxOK		= 0x04,
	RxErr		= 0x02,
	RxOK		= 0x01,

	RxAckBits	= RxFIFOOver | RxOverflow | RxOK,
};

enum TxStatusBits {
	TxHostOwns	= 0x2000,
	TxUnderrun	= 0x4000,
	TxStatOK	= 0x8000,
	TxOutOfWindow	= 0x20000000,
	TxAborted	= 0x40000000,
	TxCarrierLost	= 0x80000000,
};
enum RxStatusBits {
	RxMulticast	= 0x8000,
	RxPhysical	= 0x4000,
	RxBroadcast	= 0x2000,
	RxBadSymbol	= 0x0020,
	RxRunt		= 0x0010,
	RxTooLong	= 0x0008,
	RxCRCErr	= 0x0004,
	RxBadAlign	= 0x0002,
	RxStatusOK	= 0x0001,
};

/* Bits in RxConfig. */
enum rx_mode_bits {
	AcceptErr	= 0x20,
	AcceptRunt	= 0x10,
	AcceptBroadcast	= 0x08,
	AcceptMulticast	= 0x04,
	AcceptMyPhys	= 0x02,
	AcceptAllPhys	= 0x01,
};

/* Bits in TxConfig. */
enum tx_config_bits {
        /* Interframe Gap Time. Only TxIFG96 doesn't violate IEEE 802.3 */
        TxIFGShift	= 24,
        TxIFG84		= (0 << TxIFGShift), /* 8.4us / 840ns (10 / 100Mbps) */
        TxIFG88		= (1 << TxIFGShift), /* 8.8us / 880ns (10 / 100Mbps) */
        TxIFG92		= (2 << TxIFGShift), /* 9.2us / 920ns (10 / 100Mbps) */
        TxIFG96		= (3 << TxIFGShift), /* 9.6us / 960ns (10 / 100Mbps) */

	TxLoopBack	= (1 << 18) | (1 << 17), /* enable loopback test mode */
	TxCRC		= (1 << 16),	/* DISABLE Tx pkt CRC append */
	TxClearAbt	= (1 << 0),	/* Clear abort (WO) */
	TxDMAShift	= 8, /* DMA burst value (0-7) is shifted X many bits */
	TxRetryShift	= 4, /* TXRR value (0-15) is shifted X many bits */

	TxVersionMask	= 0x7C800000, /* mask out version bits 30-26, 23 */
};

/* Bits in Config1 */
enum Config1Bits {
	Cfg1_PM_Enable	= 0x01,
	Cfg1_VPD_Enable	= 0x02,
	Cfg1_PIO	= 0x04,
	Cfg1_MMIO	= 0x08,
	LWAKE		= 0x10,		/* not on 8139, 8139A */
	Cfg1_Driver_Load = 0x20,
	Cfg1_LED0	= 0x40,
	Cfg1_LED1	= 0x80,
	SLEEP		= (1 << 1),	/* only on 8139, 8139A */
	PWRDN		= (1 << 0),	/* only on 8139, 8139A */
};

/* Bits in Config3 */
enum Config3Bits {
	Cfg3_FBtBEn   	= (1 << 0), /* 1	= Fast Back to Back */
	Cfg3_FuncRegEn	= (1 << 1), /* 1	= enable CardBus Function registers */
	Cfg3_CLKRUN_En	= (1 << 2), /* 1	= enable CLKRUN */
	Cfg3_CardB_En 	= (1 << 3), /* 1	= enable CardBus registers */
	Cfg3_LinkUp   	= (1 << 4), /* 1	= wake up on link up */
	Cfg3_Magic    	= (1 << 5), /* 1	= wake up on Magic Packet (tm) */
	Cfg3_PARM_En  	= (1 << 6), /* 0	= software can set twister parameters */
	Cfg3_GNTSel   	= (1 << 7), /* 1	= delay 1 clock from PCI GNT signal */
};

/* Bits in Config4 */
enum Config4Bits {
	LWPTN	= (1 << 2),	/* not on 8139, 8139A */
};

/* Bits in Config5 */
enum Config5Bits {
	Cfg5_PME_STS   	= (1 << 0), /* 1	= PCI reset resets PME_Status */
	Cfg5_LANWake   	= (1 << 1), /* 1	= enable LANWake signal */
	Cfg5_LDPS      	= (1 << 2), /* 0	= save power when link is down */
	Cfg5_FIFOAddrPtr= (1 << 3), /* Realtek internal SRAM testing */
	Cfg5_UWF        = (1 << 4), /* 1 = accept unicast wakeup frame */
	Cfg5_MWF        = (1 << 5), /* 1 = accept multicast wakeup frame */
	Cfg5_BWF        = (1 << 6), /* 1 = accept broadcast wakeup frame */
};

enum RxConfigBits {
	/* rx fifo threshold */
	RxCfgFIFOShift	= 13,
	RxCfgFIFONone	= (7 << RxCfgFIFOShift),

	/* Max DMA burst */
	RxCfgDMAShift	= 8,
	RxCfgDMAUnlimited = (7 << RxCfgDMAShift),

	/* rx ring buffer length */
	RxCfgRcv8K	= 0,
	RxCfgRcv16K	= (1 << 11),
	RxCfgRcv32K	= (1 << 12),
	RxCfgRcv64K	= (1 << 11) | (1 << 12),

	/* Disable packet wrap at end of Rx buffer. (not possible with 64k) */
	RxNoWrap	= (1 << 7),
};

/* Twister tuning parameters from RealTek.
   Completely undocumented, but required to tune bad links on some boards. */
enum CSCRBits {
	CSCR_LinkOKBit		= 0x0400,
	CSCR_LinkChangeBit	= 0x0800,
	CSCR_LinkStatusBits	= 0x0f000,
	CSCR_LinkDownOffCmd	= 0x003c0,
	CSCR_LinkDownCmd	= 0x0f3c0,
};

enum Cfg9346Bits {
	Cfg9346_Lock	= 0x00,
	Cfg9346_Unlock	= 0xC0,
};

typedef enum {
	CH_8139	= 0,
	CH_8139_K,
	CH_8139A,
	CH_8139A_G,
	CH_8139B,
	CH_8130,
	CH_8139C,
	CH_8100,
	CH_8100B_8139D,
	CH_8101,
} chip_t;

enum chip_flags {
	HasHltClk	= (1 << 0),
	HasLWake	= (1 << 1),
};

#define HW_REVID(b30, b29, b28, b27, b26, b23, b22) \
	(b30<<30 | b29<<29 | b28<<28 | b27<<27 | b26<<26 | b23<<23 | b22<<22)
#define HW_REVID_MASK	HW_REVID(1, 1, 1, 1, 1, 1, 1)

/* directly indexed by chip_t, above */
static const struct {
	const char *name;
	u32 version; /* from RTL8139C/RTL8139D docs */
	u32 flags;
} rtl_chip_info[] = {
	{ "RTL-8139",
	  HW_REVID(1, 0, 0, 0, 0, 0, 0),
	  HasHltClk,
	},

	{ "RTL-8139 rev K",
	  HW_REVID(1, 1, 0, 0, 0, 0, 0),
	  HasHltClk,
	},

	{ "RTL-8139A",
	  HW_REVID(1, 1, 1, 0, 0, 0, 0),
	  HasHltClk, /* XXX undocumented? */
	},

	{ "RTL-8139A rev G",
	  HW_REVID(1, 1, 1, 0, 0, 1, 0),
	  HasHltClk, /* XXX undocumented? */
	},

	{ "RTL-8139B",
	  HW_REVID(1, 1, 1, 1, 0, 0, 0),
	  HasLWake,
	},

	{ "RTL-8130",
	  HW_REVID(1, 1, 1, 1, 1, 0, 0),
	  HasLWake,
	},

	{ "RTL-8139C",
	  HW_REVID(1, 1, 1, 0, 1, 0, 0),
	  HasLWake,
	},

	{ "RTL-8100",
	  HW_REVID(1, 1, 1, 1, 0, 1, 0),
 	  HasLWake,
 	},

	{ "RTL-8100B/8139D",
	  HW_REVID(1, 1, 1, 0, 1, 0, 1),
	  HasHltClk /* XXX undocumented? */
	| HasLWake,
	},

	{ "RTL-8101",
	  HW_REVID(1, 1, 1, 0, 1, 1, 1),
	  HasLWake,
	},
};

struct rtl_extra_stats {
	unsigned long early_rx;
	unsigned long tx_buf_mapped;
	unsigned long tx_timeouts;
	unsigned long rx_lost_in_ring;
};

struct rtl8139_private {
	void __iomem		*mmio_addr;
	int			drv_flags;
	struct pci_dev		*pci_dev;
	u32			msg_enable;
	struct napi_struct	napi;
	struct net_device	*dev;

	unsigned char		*rx_ring;
	unsigned int		cur_rx;	/* RX buf index of next pkt */
	dma_addr_t		rx_ring_dma;

	unsigned int		tx_flag;
	unsigned long		cur_tx;
	unsigned long		dirty_tx;
	unsigned char		*tx_buf[NUM_TX_DESC];	/* Tx bounce buffers */
	unsigned char		*tx_bufs;	/* Tx bounce buffer region. */
	dma_addr_t		tx_bufs_dma;

	signed char		phys[4];	/* MII device addresses. */

				/* Twister tune state. */
	char			twistie, twist_row, twist_col;

	unsigned int		watchdog_fired : 1;
	unsigned int		default_port : 4; /* Last dev->if_port value. */
	unsigned int		have_thread : 1;

	spinlock_t		lock;
	spinlock_t		rx_lock;

	chip_t			chipset;
	u32			rx_config;
	struct rtl_extra_stats	xstats;

	struct delayed_work	thread;

	struct mii_if_info	mii;
	unsigned int		regs_len;
	unsigned long		fifo_copy_timeout;

	ec_device_t *ecdev;
};

MODULE_AUTHOR("Florian Pose <fp@igh-essen.com>");
MODULE_DESCRIPTION("RealTek RTL-8139 EtherCAT driver");
MODULE_LICENSE("GPL");
MODULE_VERSION(EC_MASTER_VERSION);

module_param(use_io, int, 0);
MODULE_PARM_DESC(use_io, "Force use of I/O access mode. 0=MMIO 1=PIO");
module_param(multicast_filter_limit, int, 0);
module_param_array(media, int, NULL, 0);
module_param_array(full_duplex, int, NULL, 0);
module_param(debug, int, 0);
MODULE_PARM_DESC (debug, "8139too bitmapped message enable number");
MODULE_PARM_DESC (multicast_filter_limit, "8139too maximum number of filtered multicast addresses");
MODULE_PARM_DESC (media, "8139too: Bits 4+9: force full duplex, bit 5: 100Mbps");
MODULE_PARM_DESC (full_duplex, "8139too: Force full duplex for board(s) (1)");

void ec_poll(struct net_device *);

static int read_eeprom (void __iomem *ioaddr, int location, int addr_len);
static int rtl8139_open (struct net_device *dev);
static int mdio_read (struct net_device *dev, int phy_id, int location);
static void mdio_write (struct net_device *dev, int phy_id, int location,
			int val);
static void rtl8139_start_thread(struct rtl8139_private *tp);
static void rtl8139_tx_timeout (struct net_device *dev);
static void rtl8139_init_ring (struct net_device *dev);
static netdev_tx_t rtl8139_start_xmit (struct sk_buff *skb,
				       struct net_device *dev);
#ifdef CONFIG_NET_POLL_CONTROLLER
static void rtl8139_poll_controller(struct net_device *dev);
#endif
static int rtl8139_set_mac_address(struct net_device *dev, void *p);
static int rtl8139_poll(struct napi_struct *napi, int budget);
static irqreturn_t rtl8139_interrupt (int irq, void *dev_instance);
static int rtl8139_close (struct net_device *dev);
static int netdev_ioctl (struct net_device *dev, struct ifreq *rq, int cmd);
static struct net_device_stats *rtl8139_get_stats (struct net_device *dev);
static void rtl8139_set_rx_mode (struct net_device *dev);
static void __set_rx_mode (struct net_device *dev);
static void rtl8139_hw_start (struct net_device *dev);
static void rtl8139_thread (struct work_struct *work);
static void rtl8139_tx_timeout_task(struct work_struct *work);
static const struct ethtool_ops rtl8139_ethtool_ops;

/* write MMIO register, with flush */
/* Flush avoids rtl8139 bug w/ posted MMIO writes */
#define RTL_W8_F(reg, val8)	do { iowrite8 ((val8), ioaddr + (reg)); ioread8 (ioaddr + (reg)); } while (0)
#define RTL_W16_F(reg, val16)	do { iowrite16 ((val16), ioaddr + (reg)); ioread16 (ioaddr + (reg)); } while (0)
#define RTL_W32_F(reg, val32)	do { iowrite32 ((val32), ioaddr + (reg)); ioread32 (ioaddr + (reg)); } while (0)

/* write MMIO register */
#define RTL_W8(reg, val8)	iowrite8 ((val8), ioaddr + (reg))
#define RTL_W16(reg, val16)	iowrite16 ((val16), ioaddr + (reg))
#define RTL_W32(reg, val32)	iowrite32 ((val32), ioaddr + (reg))

/* read MMIO register */
#define RTL_R8(reg)		ioread8 (ioaddr + (reg))
#define RTL_R16(reg)		ioread16 (ioaddr + (reg))
#define RTL_R32(reg)		ioread32 (ioaddr + (reg))


static const u16 rtl8139_intr_mask =
	PCIErr | PCSTimeout | RxUnderrun | RxOverflow | RxFIFOOver |
	TxErr | TxOK | RxErr | RxOK;

static const u16 rtl8139_norx_intr_mask =
	PCIErr | PCSTimeout | RxUnderrun |
	TxErr | TxOK | RxErr ;

#if RX_BUF_IDX == 0
static const unsigned int rtl8139_rx_config =
	RxCfgRcv8K | RxNoWrap |
	(RX_FIFO_THRESH << RxCfgFIFOShift) |
	(RX_DMA_BURST << RxCfgDMAShift);
#elif RX_BUF_IDX == 1
static const unsigned int rtl8139_rx_config =
	RxCfgRcv16K | RxNoWrap |
	(RX_FIFO_THRESH << RxCfgFIFOShift) |
	(RX_DMA_BURST << RxCfgDMAShift);
#elif RX_BUF_IDX == 2
static const unsigned int rtl8139_rx_config =
	RxCfgRcv32K | RxNoWrap |
	(RX_FIFO_THRESH << RxCfgFIFOShift) |
	(RX_DMA_BURST << RxCfgDMAShift);
#elif RX_BUF_IDX == 3
static const unsigned int rtl8139_rx_config =
	RxCfgRcv64K |
	(RX_FIFO_THRESH << RxCfgFIFOShift) |
	(RX_DMA_BURST << RxCfgDMAShift);
#else
#error "Invalid configuration for 8139_RXBUF_IDX"
#endif

static const unsigned int rtl8139_tx_config =
	TxIFG96 | (TX_DMA_BURST << TxDMAShift) | (TX_RETRY << TxRetryShift);

static void __rtl8139_cleanup_dev (struct net_device *dev)
{
	struct rtl8139_private *tp = netdev_priv(dev);
	struct pci_dev *pdev;

	assert (dev != NULL);
	assert (tp->pci_dev != NULL);
	pdev = tp->pci_dev;

	if (tp->mmio_addr)
		pci_iounmap (pdev, tp->mmio_addr);

	/* it's ok to call this even if we have no regions to free */
	pci_release_regions (pdev);

	free_netdev(dev);
	pci_set_drvdata (pdev, NULL);
}


static void rtl8139_chip_reset (void __iomem *ioaddr)
{
	int i;

	/* Soft reset the chip. */
	RTL_W8 (ChipCmd, CmdReset);

	/* Check that the chip has finished the reset. */
	for (i = 1000; i > 0; i--) {
		barrier();
		if ((RTL_R8 (ChipCmd) & CmdReset) == 0)
			break;
		udelay (10);
	}
}


static __devinit struct net_device * rtl8139_init_board (struct pci_dev *pdev)
{
	void __iomem *ioaddr;
	struct net_device *dev;
	struct rtl8139_private *tp;
	u8 tmp8;
	int rc, disable_dev_on_err = 0;
	unsigned int i;
	unsigned long pio_start, pio_end, pio_flags, pio_len;
	unsigned long mmio_start, mmio_end, mmio_flags, mmio_len;
	u32 version;

	assert (pdev != NULL);

	/* dev and priv zeroed in alloc_etherdev */
	dev = alloc_etherdev (sizeof (*tp));
	if (dev == NULL) {
		dev_err(&pdev->dev, "Unable to alloc new net device\n");
		return ERR_PTR(-ENOMEM);
	}
	SET_NETDEV_DEV(dev, &pdev->dev);

	tp = netdev_priv(dev);
	tp->pci_dev = pdev;

	/* enable device (incl. PCI PM wakeup and hotplug setup) */
	rc = pci_enable_device (pdev);
	if (rc)
		goto err_out;

	pio_start = pci_resource_start (pdev, 0);
	pio_end = pci_resource_end (pdev, 0);
	pio_flags = pci_resource_flags (pdev, 0);
	pio_len = pci_resource_len (pdev, 0);

	mmio_start = pci_resource_start (pdev, 1);
	mmio_end = pci_resource_end (pdev, 1);
	mmio_flags = pci_resource_flags (pdev, 1);
	mmio_len = pci_resource_len (pdev, 1);

	/* set this immediately, we need to know before
	 * we talk to the chip directly */
	pr_debug("PIO region size == 0x%02lX\n", pio_len);
	pr_debug("MMIO region size == 0x%02lX\n", mmio_len);

retry:
	if (use_io) {
		/* make sure PCI base addr 0 is PIO */
		if (!(pio_flags & IORESOURCE_IO)) {
			dev_err(&pdev->dev, "region #0 not a PIO resource, aborting\n");
			rc = -ENODEV;
			goto err_out;
		}
		/* check for weird/broken PCI region reporting */
		if (pio_len < RTL_MIN_IO_SIZE) {
			dev_err(&pdev->dev, "Invalid PCI I/O region size(s), aborting\n");
			rc = -ENODEV;
			goto err_out;
		}
	} else {
		/* make sure PCI base addr 1 is MMIO */
		if (!(mmio_flags & IORESOURCE_MEM)) {
			dev_err(&pdev->dev, "region #1 not an MMIO resource, aborting\n");
			rc = -ENODEV;
			goto err_out;
		}
		if (mmio_len < RTL_MIN_IO_SIZE) {
			dev_err(&pdev->dev, "Invalid PCI mem region size(s), aborting\n");
			rc = -ENODEV;
			goto err_out;
		}
	}

	rc = pci_request_regions (pdev, DRV_NAME);
	if (rc)
		goto err_out;
	disable_dev_on_err = 1;

	/* enable PCI bus-mastering */
	pci_set_master (pdev);

	if (use_io) {
		ioaddr = pci_iomap(pdev, 0, 0);
		if (!ioaddr) {
			dev_err(&pdev->dev, "cannot map PIO, aborting\n");
			rc = -EIO;
			goto err_out;
		}
		dev->base_addr = pio_start;
		tp->regs_len = pio_len;
	} else {
		/* ioremap MMIO region */
		ioaddr = pci_iomap(pdev, 1, 0);
		if (ioaddr == NULL) {
			dev_err(&pdev->dev, "cannot remap MMIO, trying PIO\n");
			pci_release_regions(pdev);
			use_io = 1;
			goto retry;
		}
		dev->base_addr = (long) ioaddr;
		tp->regs_len = mmio_len;
	}
	tp->mmio_addr = ioaddr;

	/* Bring old chips out of low-power mode. */
	RTL_W8 (HltClk, 'R');

	/* check for missing/broken hardware */
	if (RTL_R32 (TxConfig) == 0xFFFFFFFF) {
		dev_err(&pdev->dev, "Chip not responding, ignoring board\n");
		rc = -EIO;
		goto err_out;
	}

	/* identify chip attached to board */
	version = RTL_R32 (TxConfig) & HW_REVID_MASK;
	for (i = 0; i < ARRAY_SIZE (rtl_chip_info); i++)
		if (version == rtl_chip_info[i].version) {
			tp->chipset = i;
			goto match;
		}

	/* if unknown chip, assume array element #0, original RTL-8139 in this case */
	i = 0;
	dev_dbg(&pdev->dev, "unknown chip version, assuming RTL-8139\n");
	dev_dbg(&pdev->dev, "TxConfig = 0x%x\n", RTL_R32 (TxConfig));
	tp->chipset = 0;

match:
	pr_debug("chipset id (%d) == index %d, '%s'\n",
		 version, i, rtl_chip_info[i].name);

	if (tp->chipset >= CH_8139B) {
		u8 new_tmp8 = tmp8 = RTL_R8 (Config1);
		pr_debug("PCI PM wakeup\n");
		if ((rtl_chip_info[tp->chipset].flags & HasLWake) &&
		    (tmp8 & LWAKE))
			new_tmp8 &= ~LWAKE;
		new_tmp8 |= Cfg1_PM_Enable;
		if (new_tmp8 != tmp8) {
			RTL_W8 (Cfg9346, Cfg9346_Unlock);
			RTL_W8 (Config1, tmp8);
			RTL_W8 (Cfg9346, Cfg9346_Lock);
		}
		if (rtl_chip_info[tp->chipset].flags & HasLWake) {
			tmp8 = RTL_R8 (Config4);
			if (tmp8 & LWPTN) {
				RTL_W8 (Cfg9346, Cfg9346_Unlock);
				RTL_W8 (Config4, tmp8 & ~LWPTN);
				RTL_W8 (Cfg9346, Cfg9346_Lock);
			}
		}
	} else {
		pr_debug("Old chip wakeup\n");
		tmp8 = RTL_R8 (Config1);
		tmp8 &= ~(SLEEP | PWRDN);
		RTL_W8 (Config1, tmp8);
	}

	rtl8139_chip_reset (ioaddr);

	return dev;

err_out:
	__rtl8139_cleanup_dev (dev);
	if (disable_dev_on_err)
		pci_disable_device (pdev);
	return ERR_PTR(rc);
}

static const struct net_device_ops rtl8139_netdev_ops = {
	.ndo_open		= rtl8139_open,
	.ndo_stop		= rtl8139_close,
	.ndo_get_stats		= rtl8139_get_stats,
	.ndo_change_mtu		= eth_change_mtu,
	.ndo_validate_addr	= eth_validate_addr,
	.ndo_set_mac_address 	= rtl8139_set_mac_address,
	.ndo_start_xmit		= rtl8139_start_xmit,
	.ndo_set_multicast_list	= rtl8139_set_rx_mode,
	.ndo_do_ioctl		= netdev_ioctl,
	.ndo_tx_timeout		= rtl8139_tx_timeout,
#ifdef CONFIG_NET_POLL_CONTROLLER
	.ndo_poll_controller	= rtl8139_poll_controller,
#endif
};

static int __devinit rtl8139_init_one (struct pci_dev *pdev,
				       const struct pci_device_id *ent)
{
	struct net_device *dev = NULL;
	struct rtl8139_private *tp;
	int i, addr_len, option;
	void __iomem *ioaddr;
	static int board_idx = -1;

	assert (pdev != NULL);
	assert (ent != NULL);

	board_idx++;

	/* when we're built into the kernel, the driver version message
	 * is only printed if at least one 8139 board has been found
	 */
#ifndef MODULE
	{
		static int printed_version;
		if (!printed_version++)
			pr_info(RTL8139_DRIVER_NAME "\n");
	}
#endif